Polímeros: Ciência e Tecnologia
https://revistapolimeros.org.br/article/doi/10.4322/polimeros.2014.026
Polímeros: Ciência e Tecnologia
Scientific & Technical Article

Mejoramiento de las Propiedades de Tensión en WPC de LDPE: HIPS/Fibra Natural Mediante Entrecruzamiento con DCP

Improvement of Properties of Tension in WPC of LDPE: HIPS/ Natural Fiber Through Crosslinking With DCP

Tobón, Arnoldo Emilio D.; Chaparro, William Arnulfo A.; Rivera, William Gómez

Downloads: 0
Views: 1202

Resumen

Fibra de Retamo Liso (teline monspessulana) fue mezclada en una matriz polimérica formada por: polietileno de baja densidad (LDPE) y poliestireno de alto impacto (HIPS) en relación 70:30 respectivamente. La fibra natural fue sometida a reducción de tamaño entre 1700 y 850 μm; se le realizó tratamiento superficial de mercerización; el contenido de humedad fue 0,17%. El análisis termo gravimétrico (TGA) muestra que la fibra tratada tiene estabilidad de 200,53 °C. La elaboración del compuesto se realizó en mezclador interno y la técnica de obtención de las probetas fue mediante moldeo por compresión. Se evaluó el efecto del agente entrecruzante peróxido de dicumilo (DCP) en compuestos con varios porcentajes de fibra: 0; 10; 25; 50 phr. La adición de DCP (1 phr) en los compuestos, mejora significativamente las propiedades de tensión con respecto a similares concentraciones de fibra; sin embargo, esta diferencia en los valores de las propiedades disminuye progresivamente cuando la cantidad de fibra se aproxima a 50 phr. El aumento en la concentración de fibra afecta negativamente las propiedades de tensión, con excepción del Módulo de Elasticidad y la Resistencia a la Fluencia. La causa principal es originada por la baja adhesión interfacial fibra natural-matriz polimérica, claramente evidenciada en las imágenes SEM.

Palabras clave

Teline Monspessulana, compuesto de plástico y madera (WPC), polietileno de baja densidad, poliestireno de alto impacto, peróxido de dicumilo

Abstract

Straight Retamo Fiber (teline monspessulana) was mixed in a polymer matrix formed by low density polyethylene (LDPE) and high impact polystyrene (HIPS) in 70:30 ratio respectively. The natural fiber was subjected to size reduction between 1700 and 850 μm; surface treatment mercerization was performed; the moisture content was 0.17%. The thermo gravimetric analysis (TGA) shows that the treated fiber has stability at 200.53 °C. The preparation of the compound was performed in internal mixer and the technique of the specimens was obtained by compression molding. The effect of crosslinking agent was evaluated: dicumyl peroxide (DCP) in compounds with various percentages of fiber: 0; 10; 25; 50 phr. The addition of DCP (1 phr) in the compounds, significantly improved tensile properties compared to similar concentrations of fiber, however, this difference in property values progressively decreases when the amount of fiber approximates 50 phr. The increase in fiber concentration negatively affects the tensile properties, except the modulus of elasticity and fluence resistance. The main cause is caused by the low interfacial adhesion natural fiber-polymer matrix, clearly evidenced in the SEM images.

Keywords

Teline Monspessulana, wood plastic composite (WPC), low density polyethylene, high impact polystyrene, dicumyl peroxide

References

1. Nabi, D. & Jog, J. – Adv. Polym. Technol., 18, p.351 (1999).

2. Westman, M. P.; Fifield, L. S.; Simmons, K. L.; Laddha, S. G. & Kafentzis, T. A. – “Natural fiber composites: a review”, U. S. Departament of Energy, Washington (2010).

3. Sullcahuamán, J. A.; Fuentes, C. A.; Mateo, M.; Pastor, A. V.; Castro, O. N. & Zabaleta, J. S. – “Materiales compuestos de cemento, papel reciclado, quitosano y refuerzo de fibras de sisal quimicamente modificadas”, en: 8° Congreso Iberoamericano de Ingeniería Mecánica, Lima (2007).

4. Mihaela, D,; Nicoleta, A.; Ghiurea, M.; Ilie, C.; Radovici, C. & Doina, M. – “Properties of Polymer Composites with Cellulose Microfibrils”, en: Advances in Composites Materials- Ecodesign and Analysis, cap.5, Attaf, B (ed.), Intech Open Acces Publisher, Rijeka Croatia (2011).

5. Lee, B.; Kim, H. & Yu, W. - Fibers and Polymers, 10, p.83 (2009).

6. Rosário, F.; Pachekoski, W.; Silveira, A.; Santos, S.; Júnior, H. & Suzan Aline Casarin, S. – Polímeros, 21, p.90 (2011).

7. Spinacé, M.; Janeiro, L.; Bernardino, F.; Grossi, T. & De Paoli M.- Polímeros, 21, p.168 (2011).

8. Ngu, H. M.; Koubaa, A.; Cloutier, A.; Soulounganga, P. & Wolcott, M. - Composites Part A: Appl. Sci. Manuf., 41, p.131 (2010).

9. Chen, H.; Chen, T. & Hsu, C. – Holz als Roh und Werkstoff, 64, p.172 (2006).

10. Balam, R. J.; Duarte, S. & Canché, G. – Rev. Mexicana de Ing. Quim., 5, p.39 (2006).

11. Cyras, V. - Revista SAM, 2, p.18 (2005).

12. Mwaikambo, L. Y. & Ansell, M. P. – “The effect of chemical treatment on the properties of hemp, sisal, jute and kapok fibres for composite reinforcement”, en: 2nd International Wood and Natural Fibre Composites Symposium, Kassel (1999).

13. Hashim, M.; Roslan, M.; Amin, A.; Ahmad, A. & Ariffin, S. – World. Acad. Sci. Eng. Technol., 68, p.1638 (2012).

14. Liu, L.; Yu, J.; Cheng, L. & Qu, W. - Composites Part A: Appl. Sci. Manuf., 40, p.669 (2009).

15. Khan, J.; Khan, M. & Islam, R. – Fibers and Polymers, 13, p.1300 (2012).

16. Pires, E.; Merlini, C.; Al-Qureshi, H.; Salmória, G. & Barra, M. – Polímeros, 22, p.339 (2012).

17. Koning, C.; Van, D. M.; Pagnoulle, C. & Jerome, R. – Prog. Polym. Sci., 23, p.707 (1998).

18. Tamboli, S.; Mhaske, S. & Kale, D. – Indian. J. Chem. Technol., 11, p.853 (2004).

19. Hieu, M. – “Compatibilization of rubber/polyethylene blends”, M. Sc. Thesis, Lulea University of Technology, Sweden (2008).

20. Siong, S. – “Effects of polystyrene modified natural rubber on the properties of polypropylene - polystyrene blends”, M. Sc. Thesis, University Sains Malaysia, Malaysia (2008).

21. Ghasemi, I. & Morshedian, J. – Iranian Polym. J., 12(2), p.119 (2003).

22. Ahmad, E. & Luyt, A. - Composites Part A: Appl. Sci. Manuf., 43, p.703 (2012).

23. Mokoena, M.; Djokovic, V. & Luyt, A. – J. Materials Sci., 39, p.3403 (2004)

24. ASTM. – “ASTM D 2765-01 – Standar Test Methods for Determination of Gel Content and Swell Ratio of Crosslinked Ethylene Plastics” (2001).

25. ASTM. – “ASTM D 638-02 – Standar Test Method for Tensile Properties of Plastics” (2002).

26. Betancourt, S.; Gañán, P.; Jímenez, A. & Cruz, L. J. – Rev. Latin. Metalurgia y Materiales, 1, p.215 (2009).

27. De La Cuesta, J.; Montoya, U.; Betancourt, S. & Álvarez, C. – Prospect, 9(2), p.75 (2011).28. Rios, A. & Martín, A. – Anales de la Mecánica de Fractura, 1, p.163 (2007).
588371a17f8c9d0a0c8b49bc polimeros Articles
Links & Downloads

Polímeros: Ciência e Tecnologia

Share this page
Page Sections