Polímeros: Ciência e Tecnologia
https://revistapolimeros.org.br/article/doi/10.1590/S0104-14282008000300005
Polímeros: Ciência e Tecnologia
Scientific & Technical Article

Efeito da Adição de Diferentes Copolímeros em Blendas HDPE/HIPS Pós-Consumo: Morfologia de Fases e Propriedades Térmicas

The Effect of Different Block Copolymers on Post Consumer HDPE/HIPS Blends: Phase Morphology and Thermal Properties

Manrich, Silvio; Manrich, Sati; Perez, Igor S. B.

Downloads: 0
Views: 904

Resumo

Blendas de poliolefinas/HIPS têm sido exploradas para obter filmes especiais com determinadas propriedades desejadas, tornando imperativo desenvolver vários estudos para um melhor conhecimento do comportamento desses materiais. Neste trabalho, efeitos da adição dos copolímeros comerciais de estireno-butadieno multibloco (SBS) e de estireno-(etilenoco- butileno)-estireno (SEBS) tribloco linear em blendas pós-consumo de HDPE e HIPS são reportados. A diminuição nas dimensões da microfase dispersa, aliada à rugosidade superficial da fase HDPE após extração seletiva do HIPS, independentemente de a fase matriz ser HIPS ou HDPE, mostraram mais eficiência do SEBS como modificador interfacial de tensão ou como surfactante entre os diferentes domínios quando comparado com o SBS. Os resultados das caracterizações térmicas, por exemplo, menor Tm e menor grau de cristalinidade do HDPE, e maior Tg do poliestireno na presença de SEBS corroboraram esta conclusão, como será discutido posteriormente.

Palavras-chave

HDPE/HIPS pós-consumo, blendas, reciclagem, compatibilização, morfologia, caracterização térmica

Abstract

Blending of post-consumer polyolefins/HIPS has been exploited for obtaining special films with a desired set of properties, which has required studies to understand the behavior of these materials. In this work the effects of commercial multiblock styrene-butadiene (SBS) and linear triblock styrene-(ethylene-co-butylene)-styrene (SEBS) copolymers in blends of post-consumer high density polyethylene (HDPE) and HIPS are reported. Thermal properties and phase morphology were comparatively analyzed for the additives aiming at verifying possible correlations between them. Decreased dimensions of the minor micro phase along with HDPE surface roughness after HIPS selective extraction, independently of the matrix being HIPS or HDPE, showed better effectiveness for SEBS as interfacial tension modifier or as surfactant at the different domains interface when compared with SBS. The results of thermal characterizations, e.g. lower HDPE melting temperature, lower degree of crystallinity, and higher polystyrene glass transition temperature in the presence of SEBS corroborated with this conclusion as it will be discussed further.

Keywords

Post consumer HDPE/HIPS, blends, recycling, compatibilization, morphology, thermal characterization

References



1. http://www.cempre.org.br, acesso em 17/10/2007.

2. Manrich, S. & Santos, A. S. F. e - "An Overview of Recent Advances and Trends in Plastic Recycling. in: Conservation and Recycling of Resources: New Research, cap.1, Christian V. Loeffe (ed.), Nova Science Publishers, Hauppauge, NY (2006).

3. Lazo, N. D. B. & Scott, C. E. - Polymer, 40, p.5469 (1999).

4. Wang, Y.; Xiao, Y.; Zhang, Q.; Gao, X-L. & Fu, Q. - Polymer, 44, p.1469 (2003).

5. Smit, I. Radonjic, G. & Hlavatá, D. - Eur. Polym. J., 40, p.1433 (2004).

6. Pospísil, J.; Fortelný, I.; Michálková, D.; Krulis, Z. & Slouf, M. - Polym. Degrad. Stab., 90, p.244 (2005).

7. Li, J. & Favis, B. D. - Polymer, 42, p.5047 (2001).

8. Galloway, J. A.; Jeon, H. K.; Bell, J. R. & Macosko, C. W. - Polymer, 46, p.183 (2005).

9. Willemse, R. C.; Speijer, A.; Langeraar, A. E. & Boer, P. - Polymer, 40, p.6645 (1999).

10. Luzinov, I.; Xi, K.; Pagnoulle, C.; Huynh-Ba, G. & Jérôme, R. - Polymer, 40, p.2511 (1999).

11. Pascu, M.; Vasile, C. & Gheorghiu, M. - Mat. Chem. Phys. 80, p.548 (2003).

12. Halimatudahliana; Ismail, H. & Nasir, M. - Polym. Test., 21, p.163 (2002).

13. Mélo, T. J. A.; Carvalho, L. H.; Calumby, R. B.; Brito, K. G. Q.; D'Almeida, J. R. M. & Spieth, E. - Polímeros: Ciência e Tecnologia, 10, p.82 (2000).

14. Faravelli, T.; Bozzano, G.; Colombo, M.; Ranzi, E. & Dente, M. - J. Anal. Appl. Pyrolysis, 70, p.761 (2003).

15. Tao, Y.; Lebovitz, A. H. & Torkelson, J. M. - Polymer, 46, p.4753 (2005).

16. Chen, B.; Li, X.; Xu, S.; Tang T.; Zhou, B. & Huang, B. - Polymer, 43, p.953 (2002).

17. Danella Jr, O. J. & Manrich, S. - Polym. Sci., 45, p.1086 (2003).

18. Santana, R. M. C. & Manrich, S. - J. Appl. Polym. Sci., 87, p.747 (2003).

19. Corrêa, A. C. & Manrich, S. - "Compatibilization of post consumer high impact polystyrene (HIPS)/high density polystyrene (HDPE) blends", in: Anais do X International Macromolecular Colloquium, Gramado - RS, Abr (2005).

20. Wu, J.; Guo, B.; Chan, C-M.; Li, J. & Tang, H-S. -Polymer, 42, p.8857 (2001).

588371247f8c9d0a0c8b4752 polimeros Articles
Links & Downloads

Polímeros: Ciência e Tecnologia

Share this page
Page Sections