Polímeros: Ciência e Tecnologia
https://revistapolimeros.org.br/doi/10.1590/S0104-14282009000300007
Polímeros: Ciência e Tecnologia
Scientific & Technical Article

Comportamento sob Fluência em Elastômeros Termoplásticos Vulcanizados Baseados em Poliamida 6 e Borracha Nitrílica

Creep Behavior of Polyamide 6/Nitrylic Rubber TPV’s Blends

Paranhos, Caio M.; Oliveira, Marcia G.; Soares, Bluma G.; Gomes, Ana C. O.

Downloads: 0
Views: 1065

Resumo

Os materiais testados neste trabalho são o resultado de um estudo do uso de aditivos e compatibilizantes na mistura de poliamida 6 (PA6) e borracha nitrílica (NBR), realizado com o objetivo de melhorar suas propriedades mecânicas e facilitar o processamento da mistura. Fluência ("creep") é um teste mecânico importante ao simular a aplicação final do material de engenharia, possibilitando a previsão do desempenho de modo comparativo. Entretanto, é um teste pouco explorado na caracterização de TPV’s. A melhora nas propriedades com a adição de aditivos e a eficiência do processo de compatibilização pode ser observada através da variação na compliância das amostras analisadas. Os resultados são correlacionados usando testes de densidade, teor de gel, resistência à tração e microscopia eletrônica de varredura. O presente trabalho mostra que é possível avaliar um material em condições semelhantes à aplicação final em um teste rápido e com gasto mínimo de material.

Palavras-chave

PA6, NBR, TPV, propriedades mecânicas, fluência.

Abstract

The materials tested in this work are the result of a study involving the use of additives and compatibilization in blends of PA6 and NBR, which was aimed at enhancing the mechanical properties and processability of the blend. Creep is an important mechanical test since it simulates the final application of the material, allowing a prediction of material performance, in a comparative way. However, this is a test seldom explored in the characterization of TPV’s. The enhancement of the properties induced by additives and the efficiency of compatibilization process can be observed through the analysis of changes in the compliance of the samples. The results are correlated using measurements of density, gel content, tension strength and scanning electron microscopy. The present work shows it to be possible to evaluate a material under conditions similar to those in the final applications, in a fast test and with minimal material waste.

Keywords

PA6, NBR, TPV, mechanical properties, creep.

References

1. Mehrabzadeh, M. & Buford, R. P. - J. Appl. Polym. Sci., 64, p.1605 (1996).

2. Mehrabzadeh, M. & Delfan, N. - J. Appl. Polym. Sci., 77, p.2057 (2000).

3. Gessler, A. M.; Haslett Jr., W. H. - U.S. Patent 3037954 (1962).

4. Kumar, R.; George, K. E. & Thomas, S. - J. Appl. Polym. Sci., 61, p.2383 (1996).

5. Rodgers, B. - “Rubber Compounding: Chemistry and Application”. Marcel Dekker Inc., New York (2004).

6. Rocha, T. C. J.; Soares, B. G. & Coutinho, F. M. B. - Pol.: Ciênc.Tecnol., 17, p.299 (2007).

7. Meyer, A. L.; Souza, G. P.; Oliveira, S. M.; Tomczak, F.; Wasilkoski, C. & Pinto, C. E. S. - Pol.: Ciênc.Tecnol., 16, p.230 (2006).

8. Coran, A. Y. & Patel, R. - Rub. Chem. Tech., 53, p.781 (1980).

9. Chowhury, R.; Banerji, M. S. & Shivakumar, K. - J. Appl. Polym. Sci., 100, p.1008 (2006).

10. Gomes, A. C. O.; Soares, B. G.; Oliveira, M. G.; Oliveira, M. F. L. & Paranhos, C. M. - e-Polymers. (2009). In press.

11. Bicerano, J. - “Creep, Stress Relaxation, Fatigue and Durability” - in: Prediction of Polymer Properties, cap. 11, J. Bicerano (ed.), Marcel Dekker, Inc., New York (2002).

12. Kolarik, J. & Pefgoretti, A. - Polym. Test. 27, p.596 (2008).

13. Menard, K. P. - “Dynamic Mechanical Analysis: A practical introduction” - CRC press, New York (1999).

14. Osamnaiye, G. J. & Adewale, K. P. - Polym. Test., 20, p.363 (2001).

15. Yang, J.; Zhang, Z.; Schlarb, A. K. & Friedrich, K. - Polymer, 47, p.2791 (2006).

16. El Fray, M. & Altstadt, V. - Polymer, 44, p.4643 (2003).

17. Almeida, M. S. M.; Soares, B. G. & Guimarães, P. I. C. - Pol.: Ciênc.Tecnol., 13, p.119 (2003).

18. Rocha, L. A. C.; Schuster, R. H.; Jacob, M. M. & Samios, D. - Pol.: Ciênc. Tecnol. 14, p.318 (2004).

20. Roguet, E.; Castagnet, S. & Grandidier, J. C. - Mech. Mat., 39, p.380 (2007).

21. Araújo, E. M.; Hage Jr., E. & Carvalho, A. J. F. - J. Mat. Sci., 38, p.3515 (2003).

22. Li, T. & Yan, N. - Composites: Part A., 38, p.01 (2007).

23. Yan, L. T.; Qian, Z. Y.; Guo, B. H.; Xu, J. & Xie, X. M. - Polymer, 46, p.11918 (2005).

24. Rangaraj, S. V. & Smith, L. V. - Mech. Time-Dep. Mat., 3, p.125 (1999).

25. Oliveira, M. G. & Soares, B. G. - Pol.: Ciênc.Tecnol., 12, p.301 (2002).

26. Passador, F. R.; Pessan, L. A.
5883715a7f8c9d0a0c8b486b polimeros Articles
Links & Downloads

Polímeros: Ciência e Tecnologia

Share this page
Page Sections