Polímeros: Ciência e Tecnologia
https://revistapolimeros.org.br/doi/10.1590/S0104-14282007000100009
Polímeros: Ciência e Tecnologia
Scientific & Technical Article

Avaliação da Orientação Molecular de Moldados de Polipropileno Utilizando Figuras de Pólo Obtidas por Difração de Raios X

Evaluation of the Molecular Orientation of Injection Molded Polypropylene Using X-Ray Pole Figures

Bretas, Rosario E. S.; Branciforti, Márcia C.; Almeida, Álvaro M.

Downloads: 0
Views: 1040

Resumo

Neste trabalho, avaliou-se a influência do perfil de velocidades de injeção utilizado durante a etapa de preenchimento na orientação molecular da fase cristalina, de amostras de polipropileno moldadas por injeção. As medidas de orientação molecular foram realizadas nas posições central e lateral da superfície de corpos-de-prova de tração injetados, utilizando figuras de pólo obtidas por difração de raios x de altos ângulos. Os resultados demonstraram que as variações na orientação molecular dos cristalitos de polipropileno estão relacionadas aos diferentes perfis de velocidades de injeção utilizados durante o processamento, sendo que um aumento na velocidade leva a um aumento do grau de orientação. Observou- se que a estrutura cristalina das moléculas do polipropileno apresenta orientação bimodal e que o grau de orientação médio é maior na posição lateral do que na posição central.

Palavras-chave

Orientação molecular, figuras de pólo, difração de raios x, polipropileno, moldagem por injeção

Abstract

In this work, the influence of the injection velocity profile on the crystalline phase molecular orientation of injection molded polypropylene samples has been evaluated. The molecular orientation has been evaluated both in the central and lateral positions on the surface of the injected tension specimens, using x-ray pole figures. The results demonstrated that the variations in molecular orientation of polypropylene crystallites were correlated to the different velocity profiles employed during the processing, showing that an increase in the velocity increases the orientation degree. It has been observed that the crystalline structure of the polypropylene molecules shows bimodal orientation and that the orientation degree at the lateral position is higher than that at the central position.

Keywords

Molecular orientation, pole figures, x-ray diffraction, polypropylene, injection molding

References



1. Pöstch, G. & Michaeli, W. - “Injection Molding: an Introduction”, Hanser, New York (1995).

2. Mendoza, R., Régnier, G., Seiler & W., Lebrun, J. L., - Polymer, 44, p.3363 (2003).

3. Yang, Y. & Gao, F. - Cont. Eng. Prac, 8, p.1285 (2000).

4. Viana, J. C., Cunha, A. M. & Billon, N. - Polymer, 43, p.4185 (2002).

5. Zhu, P. W. & Edward, G. - Polymer, 45, p.2603 (2004)

6. Phillps, R., Herbert, G., News, J. & Wolkowicz, M. - Polym. Eng. Sci., 34, p.1731 (1994).

7. Sjönell, Y., Tersulius, B., Jansson & J. F. - Polym. Eng. Sci., 35, p.950 (1995).

8. Tadmor, Z., J. - Appl. Polym. Sci., 18, p.1753 (1974).

9. Tadmor, Z., Gogos, C. G. “Principles of polymer processing”, John Wiley & Sons: New York (1979).

10. Rosato, D. V. & Rosato, D. V. “Injection Molding Handbook”, Van Nostrand Reinhold, New York (1986).

11. Strong, A. B. “Plastics: Materials and Processing”, Prentice- Hall, New Jersey (1996).

12. Rubin, I. I. “Injection Molding: Theory and Practice”, John Wiley and Sons, New York (1972).

13. White, J. L. & Spruiell, J. E. - Polym. Eng. Sci., 23, p.247 (1983).

14. Zipper, P., Eigl, F. & Geymayer, W. - Int. Polym. Proc., 12, p.192 (1997).

15. Kennedy, P. “Flow analysis of injection molds”, Hanser, New York (1995).

16. Chiu, C.P., Shin, M-C & Wei, J.H. - Polym. Eng. Sci., 31, p.1417 (1991).

17. Guo, X., Isayev, A. I. & Demiray, M. - Polym. Eng. Sci., 39, p.2096 (1999).

18. Daly, H. B., Sanschagrin, B. Nguyen, K. T. & Cole, C. - Polym. Eng. Sci., 39, p.1982 (1999).

19. Fujiyama, M. & Wakino, T., Int. Polym. Proc., 7, p.97 (1992).

20. Yu, Y. & White, J. L. - Int. Polym. Process, 18, p.388 (2003).

21. Kech, A., Ludwig, H. C., Möginger, B., Eyerer, P. & Christiansen, J. C. - Int. Polym. Process, 15, p.202 (2000).

22. Choi, D. & White, J. L. - Polym. Eng. Sci., 42, p.1642 (2002).

23. Fujiyama, M., Wakino, T. & Kawasaki, Y. - J. Appl. Polym. Sci., 35, p.29 (1988).

24. Farah, M. & Bretas, R. E. S. - J. Appl. Polym. Sci., 91, p.3528 (2004).

25. Braskem S.A.: www.braskem.com.br consultado em dezembro de 2005.

26. Almeida, A. M., “Influência da variação do perfil de velocidades de injeção na orientação molecular de moldados de polipropileno”, Tese de Mestrado, Universidade Federal de São Carlos, Brasil (2006).

27. Alexander, L. E. “X-ray Diffraction Methods in Polymer Science”, John Wiley & Sons Int., New York (1969).

28. Karger, K. J., “Polypropylene: An A-Z Reference”, Kluwer Academic Publishers, Dordrecht (1998). 29.Wilchinsky, Z. W. - J. Appl. Phys., 30, p.792 (1959).

30. Pantani, R., Coccorullo, I., Speranza, V. & Titomanlio, G. - Prog. Polym. Sci., 30, p.1185 (2005).

31. Varga, J. & Karger, J. K. - J. Polim. Sci., 34, p.657 (1996).

32. Varga, J. - J. Mat. Sci., 27, p.2557 (1992).

33. Kumaraswamy, G., Verma, R. K., Issaian, A. M., Wang, P., Kornfield, J. A., Yeh, F., Hsiao, B. S. & Olley, R. H. - Polymer, 41, p.8931 (2000). 34.Ward, I. M. “Structure and Properties of Oriented Polymers”, Applied Science Publishers, London (1975).

35. Viana, J. C. - Polymer, 46, p.11773 (2005).
588371157f8c9d0a0c8b4707 polimeros Articles
Links & Downloads

Polímeros: Ciência e Tecnologia

Share this page
Page Sections