Polímeros: Ciência e Tecnologia
https://revistapolimeros.org.br/doi/10.1590/0104-1428.1618
Polímeros: Ciência e Tecnologia
Scientific & Technical Article

Estudo comparativo da influência da razão de sopro nas propriedades de filmes tubulares de PEBD e PEAD

Comparative study of the influence of blow-up ratio in the properties of HDPE and LDPE extruded blow films

Ferreira, Roberto Luiz Rodriguez; Santana, Ruth M. C.

Downloads: 0
Views: 1746

Resumo

O objetivo deste trabalho é avaliar a influência do tipo de poliolefina e da razão de sopro (RS) nas propriedades físicas e térmicas de filmes produzidos em processo de extrusão tubular. No processamento foram utilizados um polietileno de baixa densidade (PEBD) e um polietileno de alta densidade (PEAD) transformados numa linha de extrusão de filme tubular com três RS de 1,5:1; 2,5:1 e 3,5:1. Os resultados das caracterizações físicas dos filmes mostraram maior variação de espessura no perímetro dos filmes tubulares de PEAD, quando comparados aos de PEBD. O aumento da RS causou uma diminuição de amplitude desta variação nos filmes tubulares de PEBD e diferenças nas propriedades ópticas. O coeficiente de atrito (COF) dos filmes foi menor para o PEAD e não teve variação significativa com o aumento da RS utilizada. Em relação às propriedades mecânicas, os filmes de PEAD apresentaram maior resistência à tração e menores valores de deformação no ponto de escoamento em ambas as direções. As RS maiores apresentaram similaridade nas tensões e nas deformações entre as direções da máquina (DM) e transversal (DT). A RS ideal, constatada para os filmes processados com PEBD, é 2,5:1 e com PEAD, é 3,5:1. Os filmes de PEAD apresentaram opacidade maior e menor brilho, quando comparados aos filmes de PEBD. Os resultados comprovaram valores conhecidos na literatura, entretanto introduziu-se uma inovação neste estudo: a utilização da técnica termográfica digital portátil, que permite visualizar, de maneira instantânea (on-line), as variações de temperatura no perímetro do balão, na zona de névoa (região de cristalização ou solidificação do filme).

Palavras-chave

PEBD, PEAD, PELBD, razão de sopro, linha de névoa, filme tubular, termográfica.

Abstract

The purpose of this study is to evaluate the influence of the polyolefin type and the blow-up ratio (BUR) on the thermal physical properties of films produced in a blown film extrusion process. It was used low density polyethylene (LDPE) and high density polyethylene (HDPE) processed in a blown film extrusion line at three BUR of: 1.5:1; 2.5:1 and 3.5:1. The results of physical characterization on these films demonstrated that the increase in the BUR shows a higher thickness variation in the perimeter of tubular films and, therefore, optical properties variation. The coefficient of friction (COF) of the films was smaller for HDPE and did not have significant variation with the increase in the BUR applied. Regarding mechanical properties, HDPE films showed higher tensile strength and lower strain values in the yield point, in both directions. The largest BUR showed higher similarity of the tensions and strains between the machine direction (MD) and transverse direction (TD). The ideal BUR observed for films processed with LDPE is 2.5:1, for HDPE this number is higher and close to 3.5:1. The HDPE films showed more opacities and less brightness when compared to LDPE films. The results prove well known values in the literature, however, there was an innovation introduced in this study which is the use of the portable digital thermo graphic technique that allows the instantaneous visualization (on-line) of the temperature variation in the bubble perimeter in the frost line (crystallization or solidification area of the film).

Keywords

LDPE, HDPE, LLDPE, blow-up ratio, frost line, blown film, thermographic.

References

1. Liu, C., Wang, J., & He, J. (2002). Rheological and Thermal Properties of m-LLDPE blends with m-HDPE and LDPE. Polymer, 43(13), 3811-3818. http://dx.doi.org/10.1016/S0032-3861(02)00201-X.

2. Peacock, A. J. (2000). Handbook of polyethylene: structures: properties and applications. New York: Marcel Dekker Inc.

3. Benham, E., & MacDaniel, M. (2010). Ethylene polymers – HDPE. Encyclopedia of Polymer Science and Technology, 2, 382-412.

4. Maraschin, N. ( 2010). Ethylene polymers – LDPE. Encyclopedia of Polymer Science and Technology, 2, 412-441.

5. Simpson, D. M., & Vaughan, G. A. (2010). Ethylene polymers – LLDPE. Encyclopedia of Polymer Science and Technology, 2, 441-482.

6. Brydson, J. A. (1999). Plastics materials (7th ed.). Oxford: Butterworth-Heinemann.

7. Mikitaev, A. K., Ligidov, M. K., & Zaikov Gennady, E. (2006). Polymers, polymer blends, polymer composites, and filled polymers: synthesis, properties, application. New York: Nova Science Publishers.

8. Galante, M. J., Mandelkern, L., & Alamo, R. G. (1998). The crystallization of blends of different types of polyethylene: The role of crystallization conditions. Polymer, 39(21), 5105-5119. http://dx.doi.org/10.1016/S0032-3861(97)10162-8.

9. American Society for Testing and Materials. (2008). ASTM D6988 – 08: standard guide for determination of thickness of plastic film test specimens. West Conshohocken: ASTM.

10. Associação Brasileira de Normas Técnicas. (2008). ABNT NBR 15560 - 1: filmes plásticos agrícolas para cultivo protegido – Parte 1: cobertura de estufas. São Paulo: ABNT.

11. Han Jiang et al (1999). Influence of surface roughness and contact load on friction coefficient and scratch behavior of thermoplastics olefins. Advances in Polymer Technology, 18(2), 171-180.

12. American Society for Testing and Materials. (1995). ASTM D1894-11e1: standard test method for static and kinetic coefficients of friction of plastic film and sheeting. West Conshohocken: ASTM.

13. American Society for Testing and Materials. (1999). ASTM D3418 – 99: standard test method for transition temperatures of polymers by differential scanning calorimetry. West Conshohocken: ASTM.

14. American Society for Testing and Materials. (2009). ASTM E2015 - 04: standard guide for preparation of plastics and polymeric specimens for microstructural examination. West Conshohocken: ASTM.

15. Brydson, J. A. (1999). Plastics materials (7th ed.). Wobum: Butterworth-Heinemann.

16. American Society for Testing and Materials. (2003). ASTM D1746 – 03: standard test method for transparency of plastic sheeting. West Conshohocken: ASTM.

17. American Society for Testing and Materials. (2000). ASTM D1003 – 00: standard test method for haze and luminous transmittance of transparent plastics. West Conshohocken: ASTM.

18. American Society for Testing and Materials. (1997). ASTM D2457 – 97: standard test method for specular gloss of plastic films and solid plastics. West Conshohocken: ASTM.

19. Progelhof, R. C., & Throne, J. L. (1993). Polymer engineering principles: properties, process, test for design. New York: Hanser.

20. Blass, A. (1988). Processamento de polímeros. Florianópolis: Editora da Universidade Federal de Santa Catarina.

21. Martínez-Salazar, J., Cuesta, M. S., & Plans, J. (1991). On phase separation in high- and low-density polyethylene blends: 1. Melting-point depression analysis. Polymer, 32(16), 2984-2988. http://dx.doi.org/10.1016/0032-3861(91)90197-Q.

22. Ferreira, R. L. R. (2003). Assegurando qualidade na produção de geomembranas de PEAD. Revista Engenharia, 559, 137.

23. Ferreira, R. L. R., Rempel, F. M., & Salles, C. A. (2013). Ferramentas de controle da qualidade são aplicadas na melhoria da distribuição da espessura de filmes tubulares de PEBD. Revista Plástico Industrial, 30-59.

24. Ferreira, R. L. R., Girotto, N., Salles, C. A., & Santana, R. M. C. (2011). Estudo da influência da razão de sopro na estrutura e propriedades de filmes tubulares de PEBD. In Anais do IX Simpósio Argentino de Polímeros – SAP 2011 (pp. 18). Bahía Blanca: SAP.

25. Ferreira, R. L. R., Santos, B., Konarzewski, V. H. C., & Santana, R. M. C. (2011). Avaliação da correlação de estrutura e propriedades de filmes biorientados de PEBD. In Anais do VI Congreso Internacional de Materiales - CIM 2011 (pp. 1). Bogotá: CIM.

26. Willmouth, F. M. (1986). Transparency, translucency and gloss. In F. M. Willmouth (Ed.), Optical properties of polymers (pp. 265-333). London: Elsevier.

27. White, J. L., & Cakmak, M. (1988). Orientation, crystallization, and haze development in tubular film extrusión. Advances in Polymer Technology, 8(1), 27-61. http://dx.doi.org/10.1002/adv.1988.060080105.

28. Pucci, M. S., & Shroff, R. N. (1986). Correlation of blown film optical properties with resin properties. Polymer Engineering and Science, 26(8), 569-575. http://dx.doi.org/10.1002/pen.760260808.

29. Patel, R. M., Butler, T. I., Walton, K. L., & Knight, G. W. (1994). Investigation of processing structure-properties relationships in polyethylene blown films. Polymer Engineering and Science, 34(19), 1506-1514. http://dx.doi.org/10.1002/pen.760341911.

30. Chanda, M., & Roy, S. K. ( 1987). Plastic technology handbook. New York: Marcel Dekker Inc.

31. Michaeli, W. (1992). Extrusion dies for plastics and rubber (2nd ed.). Munich: Hanser Publishers.

32. Rauwendaal, C. (2001). Polymer extrusion (4th ed.). Munich: Carl Hanser Verlag.

33. Roman, A. (1995). Transformação do polietileno – PEBD. Editora Érica Ltda.

34. Harper, C. A. (2006). Handbook of plastic processes. Wiley – Interscience. http://dx.doi.org/10.1002/0471786586.

35. Tadmor, Z., & Gogos, C. G. (2006). Principles of polymer processing (2nd ed.). Wiley – Interscience.

36. Cantor, K. (2006). Blown film extrusion: an introduction. Munich: Carl Hanser Verlag.

37. Rauwendaal, C. (1998). Polymer mixing, a self-study guide. Munich: Carl Hanser Verlag.

38. Rauwendaal, C. (1998). Understanding extrusion. Munich: Carl Hanser Verlag.

39. Rauwendaal, C. (2000). Statistical process control in injection molding and extrusion. Munich: Carl Hanser Verlag.

40. Rauwendaal, C., & Noriega, P. (2001). Troubleshooting the extrusion process. Munich: Carl Hanser Verlag.

41. Rauwendaal, C., & Cantor, K. (2001). Extrusion handbook. Munich: Carl Hanser Verlag.

42. Giles, H. F., Wagner, J. R., & Mount, E. M. (2005). Extrusion: the definitive processing guide and handbook. Norwich: William Andrew, Inc.
588371bb7f8c9d0a0c8b4a33 polimeros Articles
Links & Downloads

Polímeros: Ciência e Tecnologia

Share this page
Page Sections