Polímeros: Ciência e Tecnologia
https://revistapolimeros.org.br/article/doi/10.1590/S0104-14282009000200016
Polímeros: Ciência e Tecnologia
Scientific & Technical Article

Avaliação das Propriedades Mecânicas de Material Polimérico Utilizado na Confecção de Caixas de Medição de Energia Elétrica

Evaluation of Mechanical Properties of a Polymeric Material Used in the Construction of Boxes for Electrical Energy Measurements

Diniz, José H. de O.; Marconcini, José M.; Ruvolo Filho, Adhemar; Ferracin, Ricardo J.

Downloads: 0
Views: 956

Resumo

As propriedades mecânicas de materiais poliméricos apresentam forte correlação com o processamento do material. Neste trabalho foram estudadas blendas de poli(óxido de fenileno)/poliestireno (PPO/PS) e policarbonatos utilizados na confecção de caixas, comparando-se as propriedades mecânicas de amostras injetadas nos formatos de corpo de prova, segundo a norma ASTM D638, e de amostras retiradas diretamente das caixas. A partir dos resultados de ensaio de impacto Izod verificou-se uma grande variabilidade nos valores antes e após envelhecimento em água, de todas as caixas. Isto se deve, principalmente, às diferentes tensões internas em cada região da caixa provenientes do processamento. Também foi observada uma grande diferença entre os valores encontrados para resistência ao impacto Izod dos corpos de prova retirados da parte inferior das caixas comparados com os valores encontrados para os respectivos materiais injetados, indicando também uma significativa influência dos parâmetros de processamento de injeção, tanto nas caixas como nos corpos de prova injetados. De modo geral, os valores de resistência à tração no ponto de máxima deformação elástica não diferem significativamente entre os corpos de prova injetados e os corpos de prova retirados das caixas do mesmo material; contudo, observou-se que esta variação é significativa nos valores de alongamento à ruptura, demonstrando que esta propriedade deve ser considerada nas avaliações do comportamento mecânico dos materiais poliméricos.

Palavras-chave

Policarbonato, blenda PPO/PS, propriedades mecânicas

Abstract

The mechanical properties of polymeric materials depend strongly on the processing. In this work, blends of Poly(phenylene oxide)/polystyrene (PPO/PS) and polycarbonates used in electrical cabinet boxes have been studied. A comparison was made of the mechanical properties of samples injected in the form of test specimens, according to the standard practice ASTM D638, with test specimens removed from the boxes. From the results of impact Izod test, a great variability in the values was verified before and after ageing in water, for all the boxes. This is due to the different internal tensions in each region of the box arising from the processing. A large difference was observed among the values found for resistance to the impact Izod test of the removed test specimens of the lower part of the boxes compared with the values found for the respective injected materials. This indicates a significant influence from the parameters of injection processing, in the boxes as well as in the injected test specimens. Overall, the values of tensile strength in the point of maximum elastic deformation do not differ significantly among the test specimens injected and the removed from the boxes of the same material; however, it was observed that this variation is significant in the values of elongation at break, demonstrating that this property must be considered in the evaluations of the mechanical behavior of the polymeric materials.

Keywords

Polycarbonate, blend PPO/PS, mechanical properties

References

1. Morton-Jones, D. H. - “Polymer Processing”, Chapman & Hall, London (1994).

2. Inberg, J. P. F. & Gaymans, R. J. - Polymer, 43, p. 4197-4205 (2002).

3. Chen, S. C.; Peng, H. S.; Huang, L. T. & Chung, M. S. - J. Reinf. Plast. Comp., 22, p.479-494 (2003).

4. Ho, C. H. & Vu-Khanh, T. - Theor. Appl. Fract. Mec., 39, p.107-116 (2003).

5. Huu, C. H. & Vu-Khanh, T. - Theor. Appl. Fract. Mec., 40, p.75-83 (2003).

6. Ho, C. H. & Vu-Khanh, T. - Theor. Appl. Fract. Mec., 41, p.103-114 (2004).

7. Brydson, J. A. - “Plastics Materials”, Butterworth Heinemann, Oxford, p.584-593 (1999).

8. Ho, J.; Govaert, L. & Utz, M. - Macromolecules, 36, p.7398-7404 (2003).

9. Suzuki, T.; Yoshimizu, H. & Tsujita, Y. - Polymer, 44, p.2975-2982 (2003).

10. Sammon, C.; Yarwood, J. & Everall, N. - Polym. Degrad. Stabil., 67, p.149-148 (2000).

11. Golike, R. C. & Lasoski Jr., S. W. - J. Am. Chem. Soc., 64, p.895-898 (1960).

12. Silva, D. A.; Betioli, A. M.; Gleize, P. J. P.; Roman, H. R.; Gómez, L. A. & Ribeiro, J. L. D. - Cem. Concr. Res., 35, p.1741-1746 (2005).

13. Wa, B. Z.; Kao, C. Y. & Cheng, W. H. - Ind. Eng. Chem. Res., 40, p.509-514 (2001).

14. Ruvolo-Filho, A. & Curti, P. S. - Ind. Eng. Chem. Res., 45, p.7985-7996 (2006).

15. Mark, J.; Ngai, K.; Graessley, W.; Mandelkern, L.; E. Samulski, E., Koenig, J. & Wignall, G. - “Physical properties of polymers”, Cambridge University Press, Cambridge (2004).

16. Baschek, G.; Hartwig, G. & Zahradnik, F. - Polymer, 40, p.3433-3441 (1999).

17. Fechine, G. J. M.; Rabello, M. S.; Maior, R. M. & Catalani, L. H. - Polymer, 45, p.2303-2308 (2004).

18. La Mantia, F. P. - “Recycling of PVC and mixed plastic waste”, Chem Tec Publishing, Toronto (1996).
5883712e7f8c9d0a0c8b4782 polimeros Articles
Links & Downloads

Polímeros: Ciência e Tecnologia

Share this page
Page Sections